By Plumbing Guide for Installing a Bathtub

Call Today

Just about every person may have their own individual opinion on the subject of Tools You Need to Install a New Bathtub .


Tools You Need to Install a New Bathtub
Installing a bathtub isn't specifically rocket science, but it does require solid plumbing, carpentry, and also occasionally, tiling abilities. Changing an old tub with a brand-new one is likewise a moderately tough job. If the old tub is easily obtainable, the project can move immediately; if you have to open a wall to eliminate the old bathtub as well as place the new bath tub, the job is a lot harder. In either case, the job is within a house handyman's abilities, although you will certainly need a helper to leave the old tub and embeded in the new one. Ensure you have actually qualified yourself for the work as well as fit attempting it. Rather than hiring a professional to take over a halfway-completed task, it is better to consider using one before you start. Chances are you might need a professional plumber to make tube connections.
This article will aid you mount a new bathtub in your shower room if you have already bought a brand-new tub and also don't need to transform the setup of your previous water pipes.
Your devices and also material list ought to make up the following:
  • New Tub
  • Hammer

  • Pipe Wrenches

  • Prybar

  • Safety Glasses

  • Level

  • Pliers

  • Flexible Wrench

  • Putty Blade

  • Screwdriver

  • Cold Blade

  • Tape Measure

  • Pipeline Caps


  • Getting ready for the Installation


    Firstly, the sustaining framework provided with the bath ought to be fitted (if called for) according to the supplier's instructions. Next, fit the taps or mixer to the bath tub. When fitting the tap block, it is very important to see to it that if the faucet features a plastic washing machine, it is fitted in between the bathroom as well as the faucets. On a plastic bathroom, it is additionally reasonable to fit a supporting plate under the taps system to avoid pressure on the bath tub.
    Fit the adaptable faucet ports to the bottom of the two faucets making use of 2 nuts and also olives (occasionally provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the electrical outlet through the hole in the bathroom. Make use of the nut supplied by the manufacturer to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
    Next, fit completion of the adaptable overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bath. Make sure you use every one of the supplied washing machines.
    Connect the trap to the bottom of the waste electrical outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Connect all-time low of the overflow tube in a comparable manner.The bath must currently be ready to be suited its final setting.

    Removing Old Taps


    If you require to change old faucets with brand-new ones as a part of your installment, then the first thing you need to do is disconnect the supply of water. After doing so, switch on the faucets to drain any water staying in the system. The procedure of getting rid of the existing taps can be fairly problematic because of the limited accessibility that is frequently the situation.
    Make use of a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that connects the supply pipes to the taps. Have a towel prepared for the remaining water that will certainly originate from the pipelines. Once the supply pipelines have been removed, utilize the same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly require to stop the solitary taps from transforming during this process. Once the faucets have been gotten rid of, the holes in the bath/basin will certainly have to be cleansed of any old sealing compound.
    Before moving on to fit the new faucets, contrast the pipeline connections on the old faucets to the new faucets. If the old faucets are longer than the brand-new faucets, after that a shank adapter is required for the new faucets to fit.

    Installing the Bathtub


    Making use of both wooden boards under its feet, place the bath tub in the called for position. The wood boards are practical in equally spreading out the weight of the tub over the area of the boards instead of concentrating all the weight onto four tiny points.
    The next objective is to guarantee that the bathtub is leveled all round. This can be accomplished by checking the spirit level and also adjusting the feet on the tub till the level reads level.
    To set up faucets, fit the bottom of the furthest versatile faucet adapter to the suitable supply pipe by making a compression sign up with; after that do the very same for the other faucet.
    Switch on the water as well as examine all joints and new pipework for leakages as well as tighten them if required. Load the bathtub and also inspect the overflow outlet as well as the normal outlet for leakages.
    Finally, repair the bathroom paneling as described in the maker's user's manual. Tiling and securing around the bathtub ought to wait till the tub has been utilized a minimum of when as this will resolve it into its final setting.

    Fitting New Touches


    If the tails of the brand-new faucets are plastic, then you will require a plastic port to stop damages to the string. One end of the connector fits on the plastic tail of the tap and also the various other end offers a connection to the existing supply pipes.
    If you need to fit a monobloc, then you will require decreasing couplers, which connects the 10mm pipe of the monobloc to the basic 15mm supply pipe.
    Next off, place the tap in the placing opening in the bath/basin making sure that the washers remain in location between the faucet as well as the sink. Secure the tap in position with the supplier supplied backnut. As soon as the faucet is securely in position, the supply pipelines can be linked to the tails of the taps. The taps can either be linked by utilizing corrugated copper piping or with typical tap connectors. The former kind needs to be linked to the tap finishes first, tightening up just by hand. The supply pipes can later on be attached to the other end. Tighten both ends with a spanner after both ends have been linked.

    Tiling Around the Tub


    In the area where the bath meets the tile, it is essential to secure the joins with a silicone rubber caulking. This is very important as the fitting can move enough to fracture a stiff seal, causing the water to penetrate the wall surface between the bathroom as well as the tiling, causing problems with wetness and possible leakages to the ceiling listed below.
    You can select from a range of coloured sealants to assimilate your components and installations. They are sold in tubes and cartridges, and also are capable of securing voids approximately a size of 3mm (1/8 inch). If you have a larger gap to load, you can fill it with twists of drenched paper or soft rope. Keep in mind to always load the tub with water before securing, to enable the activity experienced when the bathtub remains in usage. The sealant can split rather very early if you do not think about this motion prior to securing.
    Alternatively, ceramic coving or quadrant floor tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are likewise quickly readily available on the market. It is a good idea to fit the tiles using water-resistant or water-proof sticky and grout.

    A Step-by-Step Guide to Installing a Bathtub


    Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.



    But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.



    This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.


    Remove the Existing Bathtub


    To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.



    The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.


    Choose the Right Bathtub


    The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.


    Install the Plumbing and Ledger Board


    You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.



    Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.


    Install the Bathtub


    When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.



    Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.



    If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.


    Hook up the Plumbing


    Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.


    Install the Bathtub Surround


    A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.



    Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.



    If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.



    If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

    https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/


    Installing A Bathtub

    As an enthusiastic reader on Installing A Bathtub, I imagined sharing that topic was smart. Do you know about somebody who is fascinated about the subject? Be sure share it. I value reading our article about How to Install a Bathtub Yourself.


    Act fast, call!

    Leave a Reply

    Your email address will not be published. Required fields are marked *